[Jul-2026] Use Real 300-615 Dumps Free Sample Questions and Practice Test Engine
Pass Cisco 300-615 exam - questions - convert Tets Engine to PDF
NEW QUESTION # 122
An engineer must configure Linux hosts that are deployed on Cisco UCS B-Series Servers to boot from SAN.
The SAN boot policy is configured in Cisco UCS Manager, and the boot order is verified to be set as expected.
However, the Linux hosts fail to boot. Which action resolves the issue?
- A. Remove all of the ISO images that are mounted as a virtual CD-ROM.
- B. Delete and reconfigure the pWWN of the SAN boot target.
- C. Remove all of the local storage that is installed.
- D. Delete and reconfigure the boot LUN.
Answer: C
Explanation:
Section: Storage Network
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/cli/config/guide/2-2/ b_UCSM_CLI_Configuration_Guide_2_2/configuring_server_boot.pdf page 5
NEW QUESTION # 123
Refer to the exhibit. To avoid service disruption, an engineer must move the server from LEAF_1 to LEAF_2. After running the test, the engineer noticed that LEAF_2 failed to forward network traffic into the VXLAN fabric. The BGP, interface NVE, and VNI were confirmed to be configured as expected. Which two actions must be taken on LEAF_2 to resolve the issue? (Choose two.)
- A. Configure correspondent IP addressing on every interface.
- B. Enable HMM tracking to advertise host routes into the VXLAN fabric.
- C. Add fabric forwarding mode anycast-gateway on interface Vlan100.
- D. Change the fabric forwarding anycast-gateway-mac MAC address.
- E. Remove ip forward from interface VIan30 and add it on interface Vlan100.
Answer: B,D
NEW QUESTION # 124
An engineer discovers that an NPV/NPIV uplink experiences a heavy load and plans to add more uplinks.
Which statement about what occurs when the new uplinks are added is true?
- A. Only new connections use the new uplinks automatically.
- B. All connections must be reset before the new uplinks can be used.
- C. Paths must be defined before new connections can use the new uplinks.
- D. New and existing connections use the new uplinks automatically.
Answer: D
Explanation:
Section: Storage Network
NEW QUESTION # 125 
Refer to the exhibit. To avoid service disruption, an engineer must move the_ server from LEAF_ 1 to LEAF_
_2. After running the test, the engineer noticed that L EAF_ 2 failed to forward network traffic into the VXLAN fabric. The BGP, interface NVE, and VNI were confirmed to be configured as expected. Which two actions must be taken on L EAF_ 2 to resolve the issue? (Choose two.)
- A. Configure correspondent IP addressing on every interface.
- B. Enable HMM tracking to advertise host routes into the VXLAN fabric.
- C. Add fabric forwarding mode anycast-gateway on interface Vlan100.
- D. Change the fabric forwarding anycast-gateway-mac MAC address.
- E. Remove ip forward from interface Vlan30 and add it on interface Vlan100.
Answer: B,D
Explanation:
Change the fabric forwarding anycast-gateway-mac MAC address; Enable HMM tracking to advertise host routes into the VXLAN fabric is the valid corrective action because the failure described is a protocol or fabric state problem, not a generic connectivity issue. For VXLAN, NVE, VNI, BGP, Cisco troubleshooting expects the engineer to compare both endpoints of the relationship: vPC peers must agree on consistency parameters, HSRP peers must exchange hellos in the same VLAN and version context, OSPF/BGP peers must match the attributes required for stable adjacency, and VXLAN EVPN must advertise the correct host or prefix information. The selected option restores that required state. The other options either operate on the wrong layer, change a value that is not used to form the relationship, or would make the peer relationship less deterministic. A clean validation is to inspect the control-plane table first, then verify the forwarding table, and finally test end-to-end traffic. This is the Cisco-preferred approach because it avoids random changes and confirms that the fabric is forwarding based on correct protocol state.
NEW QUESTION # 126
Refer to the exhibit.
An engineer must connect N2K-Fex-1 and N5K-Core-1 so that the traffic flow between the two devices uses load balancing. After inspecting the statistics of the interconnecting interfaces, the engineer concludes that only one link is used. Which action resolves the problem?
- A. Configure destination-mac load balancing on N5K-Core-1
- B. Configure each uplink to be a member of a separate LACP port channel.
- C. Configure the pinning max-link as 2.
- D. Configure source-destination load balancing on N5K-Core-1.
Answer: C
Explanation:
Explanation
https://www.cisco.com/c/m/en_us/techdoc/dc/reference/cli/n5k/commands/pinning-max-links.html
NEW QUESTION # 127
Refer to the exhibits.
An engineer troubleshoots switch N5K1, which fails to receive traffic from the file server Which set of actions resolves this problem?
- A. Bind native VLAN 10 with Ethemet10/1/1 and allow VLAN 10 in trunk configuration
- B. Bind native VLAN 10 with Ethemet1/10 and allow VSAN 101 in trunk configuration.
- C. Assign native VLAN 10 with vfc111 and allow VLAN 1101 in trunk configuration.
- D. Assign native VLAN 10 with fc2.'l - 2 and allow VLAN 10 in trunk configuration.
Answer: A
NEW QUESTION # 128
Refer to the exhibit.
The HSRP instance on both switches is showing as active. Which action resolves the issue?
- A. Allow VLAN 100 between the switches.
- B. Configure the HSRP timers to be the same.
- C. Configure the IP address of N9K-B on the same subnet as N9K-A.
- D. Configure preempt on only one of the switches.
Answer: D
NEW QUESTION # 129
Refer to the exhibit.
An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?
- A. Integrate Cisco MDS with Microsoft Active Directory.
- B. Configure SSH logins on Cisco MDS switch.
- C. Configure the role name to match the group name on Microsoft Active Directory.
- D. Include specific users into MDS role configuration.
Answer: C
Explanation:
Configure the role name to match the group name on Microsoft Active Directory is the correct fix under Cisco SAN troubleshooting practice. The issue described involves MDS, where the operating state depends on the correct combination of port type, VSAN, fabric service, and access-control database. MDS and Nexus SAN features do not infer missing policy: if the active zoneset, fabric-binding database, fcdomain, NPIV setting, or FCoE/LLDP negotiation is wrong, the link may come up physically but the initiator will not reach the target.
The selected answer corrects the missing or mismatched element. The remaining choices either act at the wrong layer, change a non-causal parameter, or provide only a temporary reset. After applying the fix, a proper Cisco validation path is to review show interface, show flogi database, show fcns database, show zoneset active, and any isolation or merge-failure logs. That confirms the storage network is operationally consistent.
NEW QUESTION # 130
Refer to the exhibit. An engineer experiences an issue presented with the Cisco UCS system.
Which action resolves the issue?
- A. Connect the adapter to the fabric interconnects using a breakout cable.
- B. Update the 1/O module firmware on the Cisco UCS chassis.
- C. Reboot the blade server and acknowledge the fault.
- D. Change the discovery policy backplane speed preference to 4x10G.
Answer: D
NEW QUESTION # 131
Refer to the exhibit. The VXLAN fabric is deployed with this configuration:
- The VLAN 50 interface has no IP address on VTEP1 and VTEP4.
- The VLAN 100 interface has no IP address on VTEP2 and VTEP3.
- nve1 interface is configured on all VTEPs.
Host A experiences timeouts when attempting to ping host B.
Which set of actions allows host A to reach host B?
- A. On VTEP2, associate VNI 30000 to Test Telco VRF.
On VTEP4, associate VNI 20000 to Test Telco VRF. - B. On VTEP1, associate VNI 50000 to Test Telco VRF.
On VTEP4, associate VNI 50000 to Test Telco VRF. - C. On VTEP2, associate VNI 55000 to Test Telco VRF.
On VTEP4, associate VNI 50000 to Test Telco VRF. - D. On VTEP1, associate VNI 30000 to Test_ Telco VRF.
On VTEP4, associate VNI 20000 to Test_ Telco VRF.
Answer: B
NEW QUESTION # 132
After upgrading a client's fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)
- A. Admin page, PollInternalBackup stage
- B. Equipment FSM page, InternalBackup stage
- C. Service profiles page, InternalBackup stage
- D. Equipment FSM page, PollInternalBackup stage
- E. Admin page, InternalBackup stage.
Answer: B,D
Explanation:
The correct action is Equipment FSM page, InternalBackup stage; Equipment FSM page, PollInternalBackup stage. Cisco UCS troubleshooting depends on the relationship between policy, inventory discovery, firmware state, and server identity. The question involves fabric interconnect, so the selected option fixes the UCS component or policy that directly controls the failure. In UCS Manager, service profiles, vNIC/vHBA templates, boot policies, firmware packages, server pools, adapters, fabric interconnects, and I/O modules are applied through a managed model; a server can fail even when basic IP reachability exists if the relevant policy is incomplete or the hardware inventory has not been acknowledged correctly. The distractors typically change an unrelated object, force a disruptive recovery without fixing the policy, or apply to a different UCS mode. Cisco guidance is to verify faults, FSM stage, inventory status, association status, and the specific boot or connectivity policy before taking action. After the remediation, validate that the fault clears, the FSM completes, and the server or fabric component returns to the expected operable state.
NEW QUESTION # 133 
Refer to the exhibit. vPC between switch1 and switch2 is not working. Which two actions are needed to fix the problem? (Choose two.)
- A. Configure one of the switches as primary for the vPC.
- B. Activate VLANs on the vPC.
- C. Match vPC domain ID between the two devices.
- D. Configure vPC peer link and vPC peer keepalive correctly.
- E. Configure IP address on the interface.
Answer: B,C
Explanation:
Section: Network
NEW QUESTION # 134
A Cisco Nexus Series interface is errdisabled with the error message "DCX-No ACK in 100 PDUs". What is the cause of this error?
- A. LLDP is disabled on the switch.
- B. The acknowledgement number in the server response has not incremented for 100 exchanges.
- C. Cisco Discovery Protocol is disabled on the switch.
- D. The host has not responded to the Control Sub-TLV DCBX exchanges of the switch.
Answer: B
Explanation:
Section: Storage Network
NEW QUESTION # 135
Refer to the exhibit. The network administrator must use a scheduler to perform configuration backups every night. After completing the configuration, the administrator discovers that configuration backups occur at 05:15 in the morning instead of at 02:00. Which action resolves the issue?
- A. Implement the switch clock to match the local time.
- B. Activate the scheduler manually at 02:00 local time.
- C. Configure the scheduler within the CONFIG_BACKUP job.
- D. Create a periodic scheduler that runs every 24 hours.
Answer: A
NEW QUESTION # 136
Refer to an exhibit.
An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?
- A. Reload the same system image.
- B. Use the same system image as the kickstart image.
- C. Load a new system image.
- D. Save the system image in NVRAM.
Answer: C
NEW QUESTION # 137
Refer to the exhibit.
An OSPF adjacency between Router-A and Router-B cannot reach the FULL state. Which action resolves the issue?
- A. Adjust the MTU on Router-B to 1604.
- B. Set the OSPF media type to point-to-point.
- C. Disable the check of the MTU value.
- D. Adjust the MTU on Router-A to 1600.
Answer: C
NEW QUESTION # 138
Refer to the exhibit.
An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?
- A. Set the local group number as 300 in the remote data center configuration
- B. Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.
- C. Run version 1 and version 2 HSRP on VLAN300 in the local data center.
- D. Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.
Answer: B
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp_fhrp/configuration/xe-16/fhp-xe-16-book/fhp-hsrp-v2.p
NEW QUESTION # 139
Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION # 140
......
Pass Your 300-615 Exam Easily - Real 300-615 Practice Dump Updated Jul 28, 2026: https://exams4sure.briandumpsprep.com/300-615-prep-exam-braindumps.html
